No one likes cleaning a toilet, but these maintenance tips will at least make the process a little easier — and less gross.
Every editorial product is independently selected, though we may be compensated or receive an affiliate commission if you buy something through our links. Ratings and prices are accurate and items are in stock as of time of publication.
Squirt-Gun Toilet Drainer
When you’re repairing or replacing a toilet, you need to remove all the water. Simply shutting off the water supply and flushing won’t do it. A sponge works, but it’s slow. So I use an old squirt gun to suck the water out and squirt it into a bucket, leaving just the last few drops to sponge out. — Dale Conklin
Use Coins for Toilet Shims
When leveling a toilet, I often use coins or washers as toilet shims. Coins or washers provide a firm seat and come in different thicknesses. Simply slide as many coins as necessary under the toilet until it’s completely level. Then caulk along the floor as you normally would to hide the coin shims. — Les Zell
Vacuum First, Then Scrub
When you wipe up bathroom surfaces with a wet sponge or rag, you may notice all the accumulated dust and hair turns into a big wet mess. Make the whole process easier by using the vacuum first. Vacuum everything from dusty light fixtures, countertops, even around the toilet. Then continue as usual with your favorite bathroom cleanerand sponge. Asoft-bristle upholstery brushworks best.
Clean a Sluggish Toilet
If your toilet flushes slowly, the rinse holes under the rim may be clogged with mineral deposits. Use a hand mirror to see the holes under the rim of the toilet. Bend a coat hanger flat and probe the tip into the holes to poke out any deposits. You can clean out those clogged holes without ever getting your hands dirty.
Remove a Toilet
Trying to pull out an old toilet? Cutting off corroded hold-down bolts with an oscillating tool is a lot faster than trying to unscrew them. Ditto for the bolts that fasten the tank to the bowl. And if the bowl is caulked to the floor, you can switch to a scraper blade and slice right through the joint.
Flush Without Hang-Ups
Here’s a quick way to avoid a running toilet caused by a kinked toilet chain.Remove the chain from the arm attachment, and slide a plastic straw over the flapper chain, covering about two-thirds of the chain. Then reattach it to the arm. It’s that simple, and you’ll never have a running toiletcaused by a kinked chain again.
Unclog a Toilet With Dish Soap
If thetoilet plungerdoesn’t seem to be doing the trick,try this solution before you reach for the snake. Squirt about 1/2 cup of liquid soap in and let it sit for a while. The liquid soap reduces friction and allows the contents of the bowl to slide on through.
Install a Detachable Toilet Seat
It seems like no matter how hard you try, you can never get the hinges on the toilet seat clean. There’s always a bit of cleaning solution that seeps underneath and creeps out later. Installing a detachable toilet seat solves the problem. Then you have easy access to clean under the hinges.
Toilet Brush Freshener
To keep your toilet brush as fresh as possible, put a splash of pine-scented cleaner in the bottom of the brush holder. This will disinfect the brush and keep your bathroom smelling clean. — Bri Aitchison
Remove Stubborn Rust Stains with Acid Magic
If you have iron in your water and struggle with rust stains in your toilet or bathtub, here’s a perfect solution. Acid Magic dissolves rust. It’s as powerful as muriatic acid but safer and more pleasant to use. You should still take all the precautions you would with any strong cleaning solution, like wearing gloves and safety glasses when you’re using it. But it’s better than regular acid because there are no noxious fumes, and it won’t burn your skin.
To clean rust from toilets and other porcelain surfaces, add one part Acid Magic to three parts water. Apply the mixture to the rust stains with a sprayer, brush or rub with a foam pad and watch the stain dissolve. Rinse with clear water. You can also full strength for stubborn stains. Avoid getting the acid on metal parts because they can discolor.
